The most reliable, flexible, and cost effective Ethernet/Internet irrigation sprinkler controller available; Use EtherRain for cost-effective, reliable Ethernet and.
Install A Dns Server On Qnap Server And WebcamGroup Policy: Mapped Drives failing to load, Windows Server 2. Active Directory and Windows Pro 1. Since I have almost no rep, I can't ask questions yet, so I'll attempt to ask a question whilst posting an answer and hope I don't get canned. I'm going to assume that you've insured that the GPO portion of this case is a non- issue, by testing this GPO against a "traditional" UNC share on another Windows system. The important missing information though in my opinion is whether or not the Synology devices are joined to the domain. A lot of Linux- based NAS units like Synology, QNAP, et al, have software components imbedded that allow them to participate in Active Directory domains. Whether or not this device is participating in the domain affects the solution. That being said, I have remote facilities in my network interconnected with T1 circuits. Install A Dns Server On Qnap Server Login![]() We require the use of Acronis imaging backups on all systems due to system requirements. Thus, remotely backing up multi- GB images of Windows workstations over T1s is a non- starter. So we placed Drobo NAS units on each local segment to overcome this and give us a bit of fault tolerance. ![]() ![]() These particular Drobos do not have the ability to participate in the AD domain. To enable the UNC shares as configured, we had to set up two main things. First, we created static DNS entries on the DNS servers to allow for proper name resolution. And second, we had to "loosen" two policies that DISA normally recommends for most domain members. We only loosened these policies on the backup server, and the workstations being backed up at "slow link" sites, as these were the only systems needing to access the respective shares: Computer Config\Windows Settings\Security Settings\Security Options. Microsoft Network Client: Digitally Sign Communications (Always) = Disabled. Microsoft Network Client: Send Uncrypted Password to Third Party SMB servers = Enabled. Microsoft Network Server: Digitally Sign Communications (Always) = Disabled. The GPOs to "Digitally Sign Communications if Negotiated" are still set to Enabled, mitigating a bit of the security risk involved. Once we enabled these changes, the shares could immediately be accessed via UNC path, whereas previously it was impossible. This is why I said earlier that depending on whether your NASes can participate in the domain or not determines the path of the solution. If they can participate, then DNS and the "SMB" group policies should be a non- issue for you, and thus the solution would lie elsewhere. If they CAN'T participate (like my NASes), then this may be your solution. How to set up VPN on QNAPLast updated: October 6, 2. This tutorial guide will walk you through the steps to set up a VPN on your. QNAP using PPTP. Jump to section. Find your Express. VPN account credentials. Login to your QNAP device. Set up a VPN connection. Connect to the VPN server. Disconnect from the VPN server. Find your Express. VPN account credentials. In order to use Express. VPN on QNAP, you will need to set up a new VPN profile. To set up a VPN profile, you will need a server address, your account credentials, and the IPSec pre- shared key. This section of the tutorial will show you how to find all of this information. Open the Welcome Email you received when you signed up for Express. VPN. Click the link in the email. If you can’t find the link, log in to your account here. Once you’ve clicked the link in the welcome email or logged into the website, click on Set Up Express. VPN on the Active Subscriptions page. Click on Manual Config on the left side of the screen and then select PPTP & L2. TP- IPSec on the right. This will show you your username, password, and a list of server addresses around the world. Please note this information as you will need it to set up your VPN profile. Need help? Contact the Express. VPN Support Team for immediate assistance. Back to top. Login to your QNAP device. Access your QNAP device and log in using your QNAP credentials. You can log in to your QNAP device here. Need help? Contact the Express. VPN Support Team for immediate assistance. Back to top. Set up a VPN connection. After logging in, go to Control Panel. Go to Applications > VPN Client. On the VPN Client setup page, select Add and then PPTP. Enter the following information (which you obtained previously) in the Create VPN Connection window: Profile Name: Select a profile name of your choice. Server Address: Copy the server address of the location that you wish to connect to from Step 1. Username: Copy username from Step 1. Password: Copy password from Step 1. Authentication: MS- CHAPv. Encryption: High (AES 1. Ensure that Use default gateway on remote network and Reconnect when the VPN connection is lost are checked. Click Apply. To add another location, repeat the above steps with the new server address. Need help? Contact the Express. VPN Support Team for immediate assistance. Back to top. Connect to the VPN server. To connect to the VPN, click the Connect button on the VPN Client page. Need help? Contact the Express. VPN Support Team for immediate assistance. Back to top. Disconnect from the VPN server. To disconnect from the VPN, click the Disconnect button on the VPN Client page. Need help? Contact the Express. VPN Support Team for immediate assistance.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
October 2017
Categories |